19/07/2024
19/07/2024 Bug in plasma nozzle usage time
26/06/2024 Bug in plasma probing range
24/06/2024 Bug in code for external driver
05/06/2024 Bug in circular stepping
15/05/2024 DSTV-NC1 import (flat sheet)
01/05/2024 Slow speed in plasma pipe cutting
10/04/2024 Extended corners in plasma mode
18/03/2024 Improvements for probing in plasma mode
18/01/2024 (Lancelot) Import settings
26/12/2023 Management of alarms on InterpCNC-3
19/12/2023 Additional import parameters
04/12/2023 Slave axis bug with InterpCNC-3
07/11/2023 Bug in AxeMotion manual control
20/10/2023 Bug in plasma probing
13/10/2023 Bug in 4-axis square section tilt
27/07/2023 Bug on cylindrical engraving in plasma
26/06/2023 CF2 import + Filter for layers & tools
19/06/2023 Bug in speed unit
15/06/2023 Cylindrial plasma cut with engraver
07/06/2023 Webcam detection of workpiece borders
31/05/2023 (Kay) Bug in serial machining
22/05/2023 Probing bug in plasma cylindric cutting
12/05/2023 Bug in import of DXF polylines
03/04/2023 (Kay) Bug in main display
16/03/2023 (Kynon) Bug in very long file names
13/03/2023 Rotation bug on "X2Y2-ok"
09/03/2023 (Kay) G32 threading cycles
17/02/2023 Zoom on machining previews
08/02/2023 GRBL axis limits
07/02/2023 Bug on 4-axis origin
31/01/2023 Bug on origin X2Y2
24/01/2023 Direct origin X2Y2 with [Ctrl] key
16/01/2023 (Percival) Pads defined as surfaces
07/01/2023 VCR-seek for cylindrical plasma cut
03/01/2023 Bug in tool compensation & pocketing
02/01/2023 Bug in kinematic slowdowns
20/12/2022 (Kay) Bug in Z-coordinates for arcs
16/12/2022 Bug in machine bed surfacing
12/12/2022 Coexistence spindle + engraving laser
10/12/2022 VCR-Seek in Kay
02/12/2022 Evaluation of the cycle time
30/11/2022 Extensions on Owein module
24/11/2022 Machining zone boundaries bug
12/10/2022 THC measurement test during the cut
07/10/2022 THC adjustment potentiometer
06/10/2022 4-axis plasma cutting for square pipes
08/09/2022 THC for Soprolec InterpCNC-3
22/07/2022 Analog camera reintegrated
01/07/2022 Passes applied to support bridge milling
24/06/2022 Manual angle lines
03/06/2022 Bug in AxeMotion homing
30/05/2022 Bug in extended joystick management
04/05/2022 Bug in process end on AxeMotion
29/04/2022 Bug in plasma kinematics calculation
07/04/2022 Turning functions (Gawain & Kay)
24/03/2022 Integration of Soprolec InterpCNC-3
13/03/2022 Bug in tool compensation
21/12/2021 Drilling points with tapping cycle
10/11/2021 Stop bug on GRBL controllers
08/10/2021 Position to reach after initialisation
16/09/2021 Tool compensation, automatic start points
06/09/2021 (Kay) G-code G53
30/08/2021 Bug of the automatic tool changer
14/08/2021 Bug in automatic support bridges
04/08/2021 Bug in VCR-Seek
19/07/2021 Bug in tool compensation with auto-entry
16/07/2021 Support bridges for plasma cut
08/06/2021 New Gaheris module for engraving images
13/05/2021 Automatic workpiece origin on webcam pads
21/04/2021 Reintegration of the webcam
26/03/2021 Tool compensation with helix plunge in
18/03/2021 Bug in tool compensation with I/O paths
05/03/2021 (Kay/Owein) Bug in G-code import
04/12/2020 Tool compensation bug on connected paths
20/11/2020 Mutual repulsion of outer tool compensations
03/11/2020 Improved calculation of tool compensation
28/10/2020 Bug in swivel blade setup
12/10/2020 Tool compensation with tangential exit
24/08/2020 (Percival) Gerber with no trailing zeros
31/07/2020 Axes reset on InterpCNC-2
17/07/2020 Bug on plasma kerf re-calculations
26/06/2020 Bug on Y-speed when jogging axes manually
23/06/2020 Helix plunge for hatches and pockets
13/05/2020 Flickering bug when objects are moved
08/05/2020 Motorised swivel blade with offset
09/04/2020 Management of obstacles on the machine
04/03/2020 4-axis milling on square-section workpiece
14/01/2020 "Parameters / Machine / Restore point"
13/12/2019 Yellow icon for lasso-selection
13/12/2019 Workpiece origin from electrical contact
22/11/2019 Bug in tool change position
20/11/2019 Sequencing functions
25/10/2019 Bug fix in serial milling process
16/05/2019 Plasma fixes
22/03/2019 Bandwidth optimisation of milling process
27/02/2019 Plasma fixes
04/02/2019 (Kay) Speed display
23/01/2019 Tool-depth-speed dialog box
26/11/2018 Bug in oblique pecks
16/10/2018 Settable pecks for each object
28/09/2018 Bug in Kay kinematics
19/09/2018 Bug on circle interpolation for Isel
31/08/2018 Optimised tool lift-ups in pecks
09/07/2018 Faster disk read/write operations
03/07/2018 "File / Gallery" bug
30/05/2018 "Touch Screen" mode
22/05/2018 IGES import
10/05/2018 Laser modulation according to speed
24/04/2018 Bug in Isel driver
22/04/2018 Bug in AxeMotion driver
18/04/2018 Plasma torch carving
28/03/2018 Milling only support bridges
20/03/2018 Bug in DXF & DWG imports
06/02/2018 Bug fixes in Kay
05/02/2018 GRBL debugging
01/02/2018 Integration of laser heads
18/01/2018 New icon "Rubout"
16/01/2018 Integration of K40 Laser Engraver
11/01/2018 Integration of Arduino GRBL cards
30/12/2017 Simplified design screen
04/12/2017 Bug in circular interpolation on contours
28/11/2017 Real-time screen monitoring of the machine
13/11/2017 (Percival) Pre-drill cycles
10/11/2017 Bug on plasma kerf change
19/10/2017 Plane correction with tool-surface contact
12/10/2017 Plane correction with workpiece surface probing
02/10/2017 ShuttleXpress parameters
26/09/2017 Bug in acknowledge timeout for plasma torch
29/06/2017 Bug in BZT safety door management
21/06/2017 Rotary milling display bug
07/06/2017 Bug in 3D angles (tool compensation)
01/06/2017 Bug in connection with isolated points
24/05/2017 Quick search for object connections
19/05/2017 Bug of tool compensation
15/05/2017 Pecks with continuous helix slope
07/05/2017 Improvements on "File / Gallery"
28/04/2017 Corrections on rotary milling
05/04/2017 Serial machining
23/03/2017 Tool compensations with automatic feed-in
31/01/2017 Bug function "Delete between intersections"
03/01/2017 Special parameters for Isel iMC machines
14/12/2016 (Kynon) Inputs displayed on screen
09/12/2016 (Percival) Isolation contour opening
21/11/2016 Access to inputs/outputs in workpiece origin
14/11/2016 Tool sensor calibration bug
05/11/2016 Circle interpolation bug with Isel machines
31/10/2016 VCR-Seek function for drill points
28/10/2016 Coupled axes on single channel, with diff. homing
25/10/2016 (Kay) "Test E/S" function
18/10/2016 Bug in welding function
14/10/2016 (Percival) Hatching bug
31/08/2016 Improvements in plasma functions
15/07/2016 Bug in VCR-seek with isolated points
21/06/2016 Bug in circular interpolation with external driver
17/06/2016 Reorganised visual dimensions
14/06/2016 THC bug on plasma torch
31/05/2016 Selection frame bug
25/05/2016 Integration of GoCNC machines
18/05/2016 Bug driving InterpCNC 1.4/1.5
13/05/2016 Management of several tool racks
14/03/2016 Table for managing sequence
10/03/2016 Plasma torch lift-up bug
09/03/2016 AI/EPS import improvement
12/02/2016 Bug in pocketing cycle islands
05/02/2016 Import/Export under Digisaf-ESSI format
03/02/2016 Isel ICV-4030 driver
13/01/2016 Small bug fixes
02/10/2015 Bug of tool compensation inside
30/09/2015 Rapid pruning functions
07/09/2015 Bug of 3D-surface probing command
04/09/2015 Improvement of machining resuming by seek
28/08/2015 FTDI addressing bug on AxeMotion 1 systems
22/07/2015 Bug in driving Isel controllers
10/07/2015 PWM-based security watchdog
15/06/2015 Milling process resuming from manual seek
11/06/2015 Crash of hatching function
12/05/2015 Optimised hatching
05/05/2015 4-axis milling bug
01/05/2015 (Percival) Improvement of hatching function
27/04/2015 Improvements on plasma torches
20/02/2015 (Kay) Bug in InterpCNC-1 control
14/02/2015 Bug of Z-origin after simulation
06/02/2015 Bug in DXF/DWG export
30/01/2015 Bug in calibration of plasma torches
28/01/2015 Bug in management of consumables for plasma torch
17/01/2015 (Percival) macros, polygonal surfaces, new calculation
16/01/2015 Bug undo/redo in memory mode (with dimensions)
22/12/2014 Standard plasma torch
19/12/2014 Manual jog bug on Solectro SML4
15/12/2014 Speed bug in exclusion zone
11/12/2014 Management of plasma torch consumables
01/12/2014 EPS/AI import bug
19/11/2014 Bug in "File / New"
18/11/2014 Automatic support bridges
22/10/2014 Bug in manual jogging with InterpCNC-2
09/10/2014 Bug in automatic text hatching
06/10/2014 Bug in support bridges
23/09/2014 Angle lines / G36-G37 polygons (Percival)
27/06/2014 Safety for manual drive from keyboard
23/06/2014 (Gawain) Sequencing functions
16/05/2014 Bug tool sensor on SM-Motion
13/05/2014 Peck in infinite loop bug
07/04/2014 "Machine / Sequence / Optimize" bug
04/04/2014 Debugging on plasma torches
18/01/2014 (Kay) Display bug
18/12/2013 Small fixes here and there
06/12/2013 Improvement of the manual drive interface
14/11/2013 Management of design templates for education
13/11/2013 Visual dimensions now active on double-click or right-click
06/11/2013 Changes for plasma torch
31/10/2013 (Gawain) Speed bug after stop
27/10/2013 Z lift-up on multiface milling
18/10/2013 (Kay) Kinematics bug on PulseBox NxtG
17/09/2013 Rounding on curve objects (nesting for marquetry)
24/07/2013 Manual drive for plasma torch
12/07/2013 Improvement in kinematics
05/06/2013 Bug in InterpCNC-1.4 driver
24/05/2013 Bug in DWG import
12/04/2013 Bug closing window at end of cycle
08/04/2013 Bug in parameters for plasma torch
31/03/2013 Bug in parameters for conical tools
27/03/2013 Bug in rounded displays of machine position
26/03/2013 (Percival) Offset using arrow keys
20/03/2013 (Percival) Reference pad #2
06/03/2013 Kinematics bug on isolated segments
13/02/2013 Tool number bug when milling process aborted
07/02/2013 Cutter plunge using oblique zigzags
28/01/2013 (Kynon) New Bezier instruction
17/01/2013 Bug fix in pocketing cycle with islands
14/01/2013 (Gawain) Export formats
26/12/2012 (Gawain) External driver
21/12/2012 Tool check at end of cycle
14/12/2012 Batch conversion of files
22/11/2012 New management of plasma torches
19/10/2012 (Percival) bug in zoom
16/10/2012 References of memorized origins
11/10/2012 (Gawain) Automatic slicing cycle
10/09/2012 (Gawain) Bug in threading parameters
27/07/2012 Bug in support bridges with full retract-up
17/07/2012 Spindle parameters, corrections for turning
09/07/2012 AxeMotion local memory management
04/07/2012 Extra pass for removing support bridges
03/07/2012 Webcam plotting: setup of crosshairs co-ordinates
29/06/2012 Rapid plunge without Z-pecks under top surface
26/06/2012 (Gawain) Automatic tool loader
25/06/2012 Z-thickness setting of support bridges
20/06/2012 Duplication sequence, option for cutting at end of cycle
31/05/2012 New function "File / Scale from points"
15/05/2012 Bug when entering a dimension from a long math expression
11/05/2012 Bug fix for analog joystick
11/04/2012 (Kay) Calculation of milling time
06/04/2012 Bug in tool listing
04/04/2012 (Percival) Scaling from distance to reference pad
16/03/2012 Points sur trace
02/03/2012 Resuming pecks after interrupt
22/02/2012 Inverted tool compensations for internal islands
16/02/2012 Background image engraving
07/02/2012 Override error at very slow speed on AxeMotion
27/01/2012 Improvements in gear icon
20/01/2012 (Percival) Diameter of centering holes
20/01/2012 Management of interrupted milling process
06/01/2012 Bug fix, import & superimposed clones
21/12/2011 Bug fix for InterpCNC-1.4
13/12/2011 AxeMotion PulseBox-NxtG driver
06/12/2011 Lathe without machine-zero
02/12/2011 Chained Z-passes in milling parameters
01/12/2011 4 axis wrapped milling
15/11/2011 Kinematics optimisation through 5-axis smoothing
08/11/2011 Management of interchangeable machine beds
12/10/2011 Initialisation sequence on AxeMotion PulseMaker 2
24/09/2011 Correction in lathe driver
16/09/2011 Exclusion zone for tool changer
29/07/2011 Bug correction, turning module
26/07/2011 (AxeMotion) Slave axes
20/07/2011 (Gawain) Memorising origin points
12/07/2011 Lateral turning
04/07/2011 Wrong speed calculation
26/06/2011 Connection on import
23/06/2011 Indexed access to PDF manual
17/06/2011 File selection dialogs
13/06/2011 Turning, inner profiling and threading
06/06/2011 Tool changes in Kay
28/05/2011 Turning on 4-axis mill
17/05/2011 Surfacing functions
16/05/2011 Percival / Centering holes
09/05/2011 Faster communication with InterpCNC-1
20/04/2011 4 axis milling
04/04/2011 5 axis control on AxeMotion Pulsar
17/03/2011 Isel IT-116 Flash controller
14/03/2011 Kinematics on AxeMotion systems
10/03/2011 DWG import
18/02/2011 AxeMotion Pulsar driver
10/02/2011 Isel-NCP import (Kay)
08/02/2011 Sigea Visio-T lathe
04/02/2011 AxeMotion Profiler-2 kit
25/01/2011 Arc functions
20/01/2011 ISO export (arcs with R tag)
18/01/2011 Essilor-OMA format
12/01/2011 DXF & ISO G-code imports
03/01/2011 DXF import, helix boring
17/12/2010 Spindle control for Isel iMC-M
01/12/2010 Buffer management on AxeMotion controllers
29/11/2010 Mobile tool sensor
23/11/2010 Spindle control on Isel CPM/ICP
17/11/2010 Correction in Isel iMC-M driver
15/11/2010 Correction in welding function for connected objects
11/09/2010 Corrections in communication layer
08/09/2010 Addition of DWG & ACL formats, corrections in DXF and EPS
29/07/2010 Correction in AxeMotion driver
26/07/2010 Tool changer with protection cap
16/07/2010 Turning module
30/06/2010 Chained pecks of depth
28/06/2010 Correction of Adobe AI/EPS import format
25/06/2010 Correction of AxeMotion PulseMaker & PulseBox drivers
14/06/2010 Integration of AxeMotion Pulsar cards with jogpad option
04/06/2010 Correction of MasterCAM-NCI import filter
31/05/2010 Control for the Z axis brake
27/05/2010 (Galaad) Linking fillets on undefined paths
22/05/2010 Fine orientation of the workpiece
06/05/2010 Correction of DXF import for splines
04/05/2010 New management of JD-Cut plasma torches
26/04/2010 Integration of Jeulin 600-CE/COM and Intelys F1000 machines
23/04/2010 Controls for JD-Cut plasma torches
19/04/2010 Origin on red cross, workpiece rotated
31/03/2010 Network-detected licence
26/03/2010 Multisided 4-axis milling
22/03/2010 Correction of a machining bug in the last update
11/03/2010 Integration of Isel ICP/MCM machines
05/03/2010 (Galaad) New functions "Design / Slot" for 3D assemblies
12/02/2010 (Percival) Automatic dispensing of SMC solder paste
26/01/2010 Management of the external keypad
20/01/2010 (Kay) Cycle start position
18/01/2010 Correction on manual drive of A axis
13/01/2010 (Galaad) Corrections on selection, arc selection filter
10/01/2010 Corrections on 4 axis milling
28/12/2009 Corrections on Isel CNC-API
15/12/2009 (Galaad) Correction on tool compensations and pocketing cycles
09/12/2009 Webcam aided origin plotting
02/12/2009 Corrections in configurable keypad
30/11/2009 Corrections in AxeMotion driver
18/11/2009 Changes in the driving of the rotary blade on C axis
09/11/2009 (Galaad) 3D wire meshes for cylindrical wrappings with 4-axes
05/11/2009 (Galaad) Corrections in selections
29/10/2009 (Percival) Automatic dispensing of SMC solder paste
23/10/2009 Corrections in 4/5 axis modes
14/10/2009 New driver for Isel/AxeMotion controllers
13/10/2009 (Percival) drilling strategy, (Kynon) ISO export
08/10/2009 (Galaad) Visual dimension bug, kaleidoscope duplication
02/10/2009 Tool comp. & pocketing, undo/redo, kinematics
22/09/2009 (Galaad) Multiple selections/unselections, binding points
30/08/2009 Communication port, improvements in Percival
31/07/2009 Integration of JDcut plasma cut machines
23/07/2009 Integration of Logosol servo controllers
21/07/2009 Integration of Isel IMC-M/P controllers
13/07/2009 Integration of AxeMotion C-142 booster card
10/07/2009 Corrections on kinematics calculation & Isel API
23/06/2009 (Galaad) Saving layer names
19/06/2009 Delayed launch of the process
18/06/2009 Correction of manual jogging with joystick/gamepad
17/06/2009 AxeMotion firmware updates
16/06/2009 (Galaad) Polyline icons
08/06/2009 (Galaad) Tool compensation with automatic start point
20/05/2009 Automatic speeds with depth pecks
19/05/2009 4 axis milling from turning module
02/05/2009 Analog laser engraving on Z modulations
27/04/2009 Floating origin mode (without machine zero)
21/04/2009 (Percival) "Undo"/"Redo" functions
16/04/2009 (Galaad) Improvements on tool compensation functions
06/04/2009 Management of Isel-Automation API DLL's
17/03/2009 (Galaad) Tool compensations without collision management
10/03/2009 (Galaad) Boring cycles
03/03/2009 (Kay) Tool cycles, (Galaad) bug fix in binding points
20/02/2009 Changes in post-processor, Jeulin-C65 driver
11/02/2009 (Percival) Boring without drill-down and lift-up at centre
08/02/2009 (Galaad) bug fix (blocked at startup)
04/02/2009 (Galaad) bug fix in text editing
29/01/2009 Registration of origins, Micrelec UPA driver
22/01/2009 Correction of Z contact margin
20/01/2009 (Galaad) Duplication on points, AxeMotion buffer management
16/12/2008 Fast USB transmission, coolant interrupt
08/12/2008 (Galaad) Bug correction for closed circles
04/12/2008 New management of the orientation C axis
26/11/2008 (Galaad) Tool compensation with single pass for finishing
25/11/2008 Correction on Kosy protocol, approach switches
24/11/2008 Correction on kinematics & cut stock base
21/11/2008 Joystick management
17/11/2008 (Percival) save current job
06/11/2008 Bug fix on kinematics for InterpCNC card
03/11/2008 (Galaad) Polygon smoothing functions
30/10/2008 (Galaad) Connections for hot-wire cutting
17/10/2008 Update for AxeMotion controllers
13/10/2008 Assistance for machine parameter calibration
29/09/2008 Correction of Sigea Visio-F parameters
26/09/2008 Corrections on kinematics calculation, multiple tool cycles
16/09/2008 AxeMotion firmware updates
15/09/2008 ISO drilling codes, visual dimensions, tool sensor
30/07/2008 Axis reassignment parameters
25/07/2008 (Galaad) tool compensation start points, 2nd tool sensor
11/07/2008 (Galaad) updating system, (Kynon) imports
07/07/2008 (Galaad) measure of distance
20/06/2008 (Galaad) binding points, InterpCNC long vectors
19/06/2008 (Galaad) vertical scrollbar, (Percival) zoom
16/06/2008 (Galaad) "Repeat" function
05/06/2008 AeroFun-CNCfun driver
02/06/2008 (Galaad) 3D zoom, AxeMotion-FlatBox driver
29/05/2008 (Galaad) Help tips, binding points